VRLA Battery

Valve Regulated Lead Acid (VRLA) Batteries are now the most common choice for modern UPS systems and use lead and lead-oxide plates immersed in sulphuric acid electrolyte. This combination develops a nominal two-volt potential from each cell.

Description

VRLA batteries are environmentally friendly and safer than earlier open-vented types. This is because modern VRLA batteries are around 98% recyclable, with well developed recycling infrastructure in most developed countries such as the reputable, trusted partners Kohler Uninterruptible Power works with.

Unlike earlier open vented cells that needed regular topping up, today’s  batteries are sealed units that require no user maintenance.  A valve allows venting of gases generated in emergency/over-pressure situations, though the amount given off is so small that it can normally be handled by standard air handling equipment used to control temperature. On this point it is important to note that as a device based on temperature dependent chemical reactions, batteries require a temperature-controlled environment. The best balance between operating performance and lifetime is achieved at 20degrees C. As a rule of thumb, for every 10 degrees C above this the working life will halve. The useful working life of the battery is also affected by  how the battery is used, so great care must be taken when selecting and sizing batteries for a UPS installation.

VRLA batteries can be housed in cabinets alongside the UPSs rather than in separate battery rooms, even if the UPSs are operating within an office environment. However, because the combined voltage of the battery system will be the same as a mains electricity supply, for safety reasons it should be protected from unauthorised or accidental contact.

All batteries should be regularly checked or a fixed battery monitoring system should be used. Eventually, they will require replacement, however, this life can be maximised by taking care to operate within a well-managed environment and setting up a regular maintenance schedule. A battery management system that balances charging between battery “blocks” can also be added, potentially increased lifetime by up to 30%.

VRLA batteries are made up in blocks; a battery block is a number of cells connected together with a given voltage and capacity, where. the capacity is defined in terms of Ampere hours (Ah). The more cells the higher the battery voltage and the larger the plates the higher the battery capacity.

Batteries are generally made in 12-volt blocks using six cells but are also available in 6-volt (three cell), 4-volt (two cell) and 2-volt (single cell) blocks. In the battery configuration, all the cells used in a serial string must be identical to each other.

Disposal/Recycling

When a battery has reached the end of its useful working life it must be returned to the point of sale or to a licensed battery dealer for recycling. ‘Old’ batteries are classified as ‘hazardous waste’ and must be disposed of in line with current legislation. Kohler Uninterruptible Power can assist with the disposing/recycling of VRLA batteries.

What is a battery?

A battery is a device that uses chemical means to store electrical energy and can be found in any number of shapes, sizes, voltages and capacities.

When two materials (usually dissimilar metals) are immersed in a solution (electrolyte) they conduct electricity between the ‘plates’ which gives rise to an electrical potential. The value of the potential (or voltage) depends on the plate materials and the electrolyte used. Examples of different battery composition include lead-acid, nickel cadmium (Ni-Cad), and lithium-ion.

Documentation

    GET A QUOTE

    Are you interested? Call us on 01256 386700 or complete the form below, and let us supply you with a quote. Required Info*








    We would like to keep in touch with you from time to time! If you would like to hear from us, please let us know what you are interested in:

    To learn more about these options and what they mean, please view our Marketing Communications page.

    Related products

    • PowerWAVE 6000

      Three phase
      Three phase
      A three-phase installation uses the full three phases which are generated from the grid. A three phase electrical supply comprises of three individual sine waves, and can be installed as either a three wire or three wire & neutral configuration. A three-phase source would typically come from a local transformer, with the standard three phase voltage being 400/415 VAC.
      60-500 kVA (500kW)
      60-500 kVA (500kW)
      Understanding the total kVA requirement of a critical load is a key part of establishing a UPS’ true sizing requirement. For more information see kVA calculator and guide to choosing a UPS.
      Standalone
      Standalone
      Standalone UPS systems allow several units to be operated in tandem (known as horizontal scaling) to provide for a greater load.
      Transformerless 3 phase UPS from 60 kVA to 500 kVA, parallelable up to 5 MVA. Offering both intellig
      Read MoreCompare
    • PowerWAVE 8000DPA

      Three phase
      Three phase
      A three-phase installation uses the full three phases which are generated from the grid. A three phase electrical supply comprises of three individual sine waves, and can be installed as either a three wire or three wire & neutral configuration. A three-phase source would typically come from a local transformer, with the standard three phase voltage being 400/415 VAC.
      10-200 kVA per frame
      10-200 kVA per frame
      Understanding the total kVA requirement of a critical load is a key part of establishing a UPS’ true sizing requirement. For more information see kVA calculator and guide to choosing a UPS.
      Modular
      Modular
      UPS systems such as the PowerWAVE 9000DPA Series are configured by plugging up to five modules into a 19” rack to meet the capacity and redundancy requirement of the application load. This provides more flexibility and scalability than a complete cabinet containing a single standalone system.
      Three-phase UPS built for low to medium, high density power protection applications. Leading-edge mo
      Read MoreCompare
    • PowerWAVE 9000DPA (Modular 10-250kVA)

      PowerWAVE 9000DPA

      Three phase
      Three phase
      A three-phase installation uses the full three phases which are generated from the grid. A three phase electrical supply comprises of three individual sine waves, and can be installed as either a three wire or three wire & neutral configuration. A three-phase source would typically come from a local transformer, with the standard three phase voltage being 400/415 VAC.
      30-250 kVA
      30-250 kVA
      Understanding the total kVA requirement of a critical load is a key part of establishing a UPS’ true sizing requirement. For more information see kVA calculator and guide to choosing a UPS.
      Modular
      Modular
      UPS systems such as the PowerWAVE 9000DPA Series are configured by plugging up to five modules into a 19” rack to meet the capacity and redundancy requirement of the application load. This provides more flexibility and scalability than a complete cabinet containing a single standalone system.
      A revolutionary rack-mounted uninterruptible power supply designed with ‘hot swap’ modules for futur
      Read MoreCompare
    • PowerWAVE 9250DPA

      PowerWAVE 9250DPA

      Three phase
      Three phase
      A three-phase installation uses the full three phases which are generated from the grid. A three phase electrical supply comprises of three individual sine waves, and can be installed as either a three wire or three wire & neutral configuration. A three-phase source would typically come from a local transformer, with the standard three phase voltage being 400/415 VAC.
      Modular
      Modular
      UPS systems such as the PowerWAVE 9000DPA Series are configured by plugging up to five modules into a 19” rack to meet the capacity and redundancy requirement of the application load. This provides more flexibility and scalability than a complete cabinet containing a single standalone system.
      True modular uninterruptible power supply, scalable from 50kW up to 1.5MW, for medium power applicat
      Read MoreCompare
    • PowerWAVE 9500DPA (Modular 100-500kVA)

      PowerWAVE 9500DPA

      Three phase
      Three phase
      A three-phase installation uses the full three phases which are generated from the grid. A three phase electrical supply comprises of three individual sine waves, and can be installed as either a three wire or three wire & neutral configuration. A three-phase source would typically come from a local transformer, with the standard three phase voltage being 400/415 VAC.
      100-500 kVA
      100-500 kVA
      Understanding the total kVA requirement of a critical load is a key part of establishing a UPS’ true sizing requirement. For more information see kVA calculator and guide to choosing a UPS.
      Modular
      Modular
      UPS systems such as the PowerWAVE 9000DPA Series are configured by plugging up to five modules into a 19” rack to meet the capacity and redundancy requirement of the application load. This provides more flexibility and scalability than a complete cabinet containing a single standalone system.
      Innovative 5 x 100kW modular UPS system offering pay-as-you-grow scalability combined with 99.9999%
      Read MoreCompare
    Top

    Pin It on Pinterest

    Share This